Pea Gravel vs #57 Stone for Drainage: Which One to Use

By Ali (not a contractor)Updated

Pea gravel drains water, but washed #57 stone is the better pick for a French drain, a dry well or the backfill behind a retaining wall. #57 is angular crushed stone, roughly 1/2 to 1 inch, with about 40 percent open space, and it is the stone that state stormwater manuals and wall makers name. Pea gravel (round, about 3/8 inch) costs nearly the same in this site’s price data, $38 a ton against $40 for #57, so price is no reason to choose it.

The two stones side by side

Detail Pea gravel #57 stone
Size about 3/8 in roughly 1/2 to 1 in
Shape round, water-worn angular, crushed
Open space no tested figure found about 40 percent
Weight per cubic yard 1.4 tons (1.3 to 1.5) 1.4 tons (1.3 to 1.5)
Price per ton $38 ($25 to $55) $40 ($22 to $75)
Price per cubic yard $53 ($30 to $80) $56 ($30 to $90)

The prices are this site’s national typical figures, and your yard will differ. Delivery usually adds $0 to $150, typically $75.

How much room for water

The only tested open-space figure belongs to #57. Virginia’s stormwater spec designs with a void ratio of 0.4 for No. 57 stone, Minnesota’s manual asks for at least 40 percent in the stone layer under permeable pavement, and New Hampshire’s homeowner dry well guide says washed stone leaves about 40 percent of the space for water. No tested figure for pea gravel turned up, so this guide does not print one.

Bigger gaps move water faster. The standard grain-size formulas scale flow with the square of the grain size, so a stone twice as big moves about four times the water. Those formulas were built mostly for sand, so treat that as a rough direction for gravel. It rarely decides a yard job anyway. The federal highway drainage guide calls 1,000 feet a day excellent for an open stone layer and, in wet climates, suggests adding drains when soil passes less than 10 feet a day, so either stone is likely far faster than the dirt around it. Drains usually fail from silt, which the section on washed stone covers.

Round vs angular stone

#57 is crushed, so the faces are rough and the pieces lock when you tamp them. A pavement-products spec sheet calls it self-compacting: a plate compactor orients the stones and the layer settles about 8 percent. Round pea gravel rolls over itself, which is why it shifts underfoot and why shed builders tell you to skip it as a base.

Shape matters where something stands on the stone, such as patios, walkways and sheds. It matters less in a buried drain. Allan Block’s own wall guide allows “angular or smooth” wall rock, as long as it has no sand, silt or clay in it.

What the specs say about drains

The model residential building code (IRC R405.1), for a drain at a basement footing, calls for at least 2 inches of washed gravel or crushed rock under the pipe and at least 6 inches of the same stone over it. The stone must be at least one sieve size larger than the pipe’s holes, with a filter membrane around it. A paving-industry guide describes a typical 4 inch drain pipe surrounded by at least 3 inches of No. 57 or similar open-graded stone, wrapped in geotextile.

Pea gravel runs into trouble with that hole-size rule. Pea gravel is about 3/8 inch, and Virginia’s PVC underdrain spec uses 3/8 inch holes, so stone the size of the holes can work into the pipe. Check the holes on the pipe you bought. Most #57 is larger than 3/8 inch, so it stays out of a pipe with holes that size.

For walls, Redi-Rock prefers ASTM No. 57 with nothing passing the No. 200 sieve, and Allan Block and Redi-Rock both want at least 12 inches of drainage stone behind the wall. Keystone specifies clean 1 inch minus crushed stone, and Versa-Lok wants angular, clean stone. For dry wells, New Hampshire’s guide uses 1/2 to 1 1/2 inch washed stone, and a Massachusetts planning council factsheet says 1.5 to 3 inch washed, crushed stone. Pea gravel is smaller than either.

Which stone for which job

Job Use Why
French drain Washed #57 Matches the specs, stays out of pipe holes
Dry well Washed #57 or bigger Guides say 1/2 to 3 inch washed stone
Behind a retaining wall #57 Redi-Rock prefers it, 12 inch zone
Footing drain #57 Code wants washed stone bigger than the holes
Under a downspout Pea gravel is fine A splash pad holds soil, carries no load
Pipe bedding Either Suppliers sell both for it
Walkway surface Pea gravel Soft underfoot, but edge it
Patio or walkway base Crushed stone Unilock: 6 to 8 inches, compacted
Under a shed #57 or 3/4 inch crushed 4 to 6 inches, compacted

On a regular paver patio the base is compacted crushed stone with fines (crusher run). #57 is the open-graded base for permeable pavers.

Washed stone and fabric

Fines are the usual cause of failure. The federal highway guide says free-draining stone layers have no fines (0 percent passing the No. 200 sieve) and puts a clean layer above 1,000 feet a day. It puts a dense base with under 5 percent fines at about 1 foot a day, a thousandfold drop from a little dust. Virginia asks for double-washed stone “free of all fines” for the layers that carry water. One quarry’s test report on #57 shows 0.4 percent passing the No. 200 sieve, so properly washed stone is nearly dust-free.

Buy by name: ask for “washed 57” or “clean 57”. Crusher run, quarry process and stone dust compact because they carry fines, and the fines choke a drain.

Wrap the stone in non-woven geotextile so soil cannot move in. The IRC calls for a filter membrane around gravel drains, the ICPI guide uses geotextile to stop soil migrating into stone, and New Hampshire lines dry wells with non-woven fabric. Line the bottom and both sides, then fold the fabric over the top before you backfill. A 12 inch by 18 inch trench needs 48 inches across before the fold, so buy a roll 5 or 6 feet wide.

Worked example: a 50 ft French drain

Say you dig 50 ft long, 12 inches wide and 18 inches deep, with a 4 inch pipe. Eighteen inches is the top of the drainage range in the gravel calculator, and Kirk Allen Landscape Supply puts typical trenches at 18 to 24 inches deep.

  • Trench: 50 ft x 1 ft x 1.5 ft = 75 cubic feet.
  • Pipe: 3.14 x (2/12 ft)^2 x 50 ft = 4.4 cubic feet.
  • Stone: 75 minus 4.4 = 70.6 cubic feet, which is 2.6 cubic yards (70.6 divided by 27).
  • Add 10 percent for settling and spill, the waste figure in this site’s data for both stones: 2.9 cubic yards.
  • Weight at 1.4 tons a cubic yard: about 4.0 tons (3.7 to 4.3 across 1.3 to 1.5).
  • Cost at typical prices: pea gravel 4.0 x $38 = $153, and #57 4.0 x $40 = $161, before delivery.

Order about 3 cubic yards or 4.5 tons, since the calculators round an order up to the next half. If you cap the trench with 6 inches of soil or sod, the stone is 12 inches deep: 1.9 cubic yards or 2.6 tons, so order 2 yards or 3 tons.

The calculators do not subtract the pipe, so entering 50 x 1 x 1.5 reads about 6 percent high, which is a fair cushion. Use the cubic yards to tons calculator to switch units for your supplier, and the rock calculator if you are pricing river rock.

When pea gravel is the right call

Pea gravel suits places where nothing heavy stands on it and no pipe hole can swallow it: a walking surface (Ozinga calls it comfortable underfoot, and this site’s material notes say to edge paths), play areas, a thin layer over a finished drain, a splash pad under a downspout, and pipe bedding. For a French drain, #57 costs about $2 more a ton and is the stone the specs name.

Seller claims nobody has tested

Gravel sellers disagree, and some contradict themselves. One seller’s guide says pea gravel is “excellent for French drains” and drains at 15 to 20 inches an hour, while another guide from the same company calls it “a poor choice for a functional french drain”. A third site says it is “prone to packing together to form a solid mass”. None of them cite a test, and no test turned up.

If your pipe holes are small and the pea gravel is washed, the code wording (“washed gravel or crushed rock”) covers it. You give up margin: smaller gaps between stones, and holes the stone can enter.

Calculators for this job