Rebar Calculator
Bars, sticks, weight, ties and chairs for a slab.
#4 rebar weighs 0.668 lb per foot, 13.36 lb per 20 ft stick; a 20 ft span at 18 in on center takes 15 bars.
#4 weighs 0.668 lb per foot.
Each way. 12 to 24 in: 18 to 24 for a 4 in slab, 12 to 18 for a 6 in slab.
3 in for concrete cast against the ground (ACI 318).
Slab
Bars over 20 ft are spliced: 24 in laps (48 bar diameters). Ties: 119 (every other of 238 crossings). Chairs: about 54 (one per 9 sq ft).
- Slab: 24 × 20 ft
- Bar: #4 (1/2 in)
- Spacing: 18 in on center, each way
- Edge cover: 3 in
- Stick: 20 ft, lap 48 bar diameters
- Ties: every other crossing
Prices & extras
Rebar is sold in 20 ft (6.1 m) sticks. Use the length your yard sells.
48 diameters is 24 in for #4. Try 30 to 60.
Tie wire holds the grid together while you pour.
Chairs hold the bars off the ground. Skip them if you lift the mat by hand.
Laps and the cut plan are already counted. Add a little for bad cuts.
Optional. Type your yard’s price for one stick.
A 24 by 20 ft slab with #4 rebar 18 in apart each way needs about 36 sticks of 20 ft rebar, about 460 lb in all.
How to use the rebar calculator
- Type the slab’s length and width. Add another slab for each pad, such as a driveway and a walk, and the totals are summed.
- Pick the bar size. #4 is the default. The hint under the box shows what that bar weighs per foot.
- Set the spacing, measured on center and used in both directions. Then set the edge cover, the gap between the end of a bar and the edge of the slab.
- Open Prices & extras to change the stick length, the splice lap, how you tie the grid, the chair spacing, extra for waste and the price of a stick.
This estimates quantities, not structural design. Check your local building code.
How the rebar calculator works
Each slab gets a grid. The bars end the cover short of every edge, so the calculator first takes the cover off both sides of the length and the width. Bars that run along the length are counted across the width: the width span divided by the spacing, rounded up, plus one bar so there is one at each end. Bars that run across the width are counted the same way along the length. Rounding up means no gap is wider than the spacing you chose.
A bar longer than a stick has to be spliced. The calculator lays the overlap at 48 bar diameters by default: 18 in for #3, 24 in for #4, 30 in for #5 and 36 in for #6. Each extra piece adds one lap, so a long bar costs more than its plain length. If a bar needs more than 20 pieces the calculator tells you to use longer sticks instead.
The sticks number comes from a cut plan, not from dividing the total length by 20. A bar that needs two pieces uses one full stick plus a short piece from a second stick, and several of those short pieces share a stick. A 19.5 ft bar fills a stick and leaves a scrap too short to use, so dividing the total length would under-buy. The plan counts what you can really cut.
Weight is the bar length with laps times the weight per foot of that bar. Ties are counted at the crossings of the grid, either every other crossing or every one. Chairs are counted from the slab area: one for each square of the spacing you pick, which is about one per square yard at 3 ft.
The calculator counts material only. It does not choose a bar size or a spacing for your slab, and it does not size footings, walls or stirrups.
Rebar sizes
A #4 bar weighs 0.668 lb per foot and laps 24 in. Weights are the standard figures for the bars sold in the US, with the lap at 48 bar diameters.
| Bar | Dia. (in) | lb per ft | Lap (in) |
|---|---|---|---|
| #3 | 0.375 | 0.376 | 18 |
| #4 | 0.5 | 0.668 | 24 |
| #5 | 0.625 | 1.043 | 30 |
| #6 | 0.75 | 1.502 | 36 |
Spacing used on home slabs
A 4 in slab typically has bars 18 to 24 in apart each way, a 5 in slab 16 to 20 in and a 6 in slab 12 to 18 in. These ranges come from slab guides and are context only. Your slab design or local code decides.
| Slab thickness | Typical spacing, each way |
|---|---|
| 4 in | 18 to 24 in |
| 5 in | 16 to 20 in |
| 6 in | 12 to 18 in |
Against the ground, the ACI concrete code asks for 3 in of cover between the steel and the soil, so the calculator starts with 3 in. You can set it from 0 to 6 in. Cover here only shortens the bars and shrinks the grid, so it is a layout setting and not a code check.
Ties, chairs and what to buy
Tie wire holds the mat together while you pour. Tying alternate crossings is the usual pattern, and the calculator counts every other crossing unless you switch it. Chairs lift the grid off the ground so the bars end up inside the slab, where your plan puts them.
Cap or guard any cut bar ends that stick up: a fall onto a bare bar can impale, and OSHA requires protruding rebar on job sites to be guarded.
Buy the sticks, chairs and tie wire together, and add a little for bad cuts if you want a spare stick on site. The extra box adds a share to the stick count only.
Worked example
- Slab: 24 ft × 20 ft = 480 sq ft
- Inside the edge cover: 24 − 2 × 0.25 = 23.5 ft by 20 − 2 × 0.25 = 19.5 ft
- Bars along the length: 19.5 ft ÷ 1.5 ft = 13, round up and add 1 = 14 bars of 23.5 ft
- Bars along the width: 23.5 ft ÷ 1.5 ft = 15.67, round up and add 1 = 17 bars of 19.5 ft
- Laps: 48 bar diameters × 0.5 in = 24 in per splice
- Bar length with laps: 688.5 ft, at 0.668 lb per foot = 460 lb
- Cutting 14 bars of 23.5 ft: 2 pieces each, so 14 full sticks plus 5 sticks for the 5.5 ft last pieces (3 per stick)
- Sticks: 19 for the bars along the length + 17 along the width = 36 sticks of 20 ft
- Ties: 238 crossings ÷ 2 = 119
- Chairs: 480 sq ft ÷ 9 sq ft = about 54
Questions people ask
How much rebar do I need for a slab?
A 24 by 20 ft slab with #4 bars at 18 in on center and 3 in of cover needs 688.5 ft of bar once the splices are counted, which is 36 sticks of 20 ft when the leftover pieces are reused. Rebar runs both ways. Each direction takes the span divided by the spacing, rounded up, plus one bar, and each bar is about a slab side long, less the cover at the edges.
How far apart should rebar be in a slab?
Home slabs usually run 12 to 24 in on center each way: 18 to 24 in for a 4 in slab, 16 to 20 in for 5 in, and 12 to 18 in for 6 in. The ACI concrete code caps shrinkage and temperature steel at the lesser of 5 times the slab thickness or 18 in. Your local code and your slab design set the real number.
What size rebar do I use for a concrete slab?
#3 (3/8 in) is common for 4 in patios and walks, and #4 (1/2 in) for 6 in slabs and driveways. #4 weighs 0.668 lb per foot, just over 13 lb for a 20 ft stick, and #3 weighs 0.376 lb per foot. The heavier the bar, the fewer you can use at a wider spacing, but the bar size is a design choice, not something this page can decide.
How long should rebar overlap at a splice?
A common rule of thumb for home work is 24 to 30 in of overlap for #3 and #4 bars. Engineers often use 48 bar diameters for Grade 60 steel, which is 24 in for #4, and this page does the same by default. You can change it from 30 to 60 diameters. Tie each splice with wire, and ask your inspector for the exact lap.
How many rebar chairs do I need?
Space chairs about 3 to 4 ft apart in each direction, roughly one for every square yard of slab. The calculator uses 3 ft by default and 4 ft as the other choice. Pick chairs that hold the bars at the depth you want inside the concrete.
How much does rebar cost?
A 20 ft #3 stick cost $4.13 to $7.59 at two suppliers, and thicker bars cost more. Prices follow steel and change by region and supplier. The calculator starts with the price blank on purpose: type your yard's price per stick to get a cost.