Asphalt Calculator
Tons of hot-mix asphalt for a driveway or parking area, with cost and the gravel base.
Hot-mix asphalt weighs about 1.98 tons per cubic yard, so 1 ton covers about 82 sq ft at 2 in compacted.
Driveway, cars: 2-3 in deep. Compacted asphalt over a 6 to 8 in stone base.
Area 2
1 ton covers about 82 sq ft at 2 in.
- Area: 50 × 12 ft, 2 in deep
- Material: Hot-mix asphalt
- Extra: 10%
- Bulk price: $100/ton
Installed cost and base
New driveway $5 to $15 per sq ft; over an old driveway $2 to $7
Paved by a contractor: about $6,000 (range $3,000 to $9,000) for 600 sq ft.
Under the asphalt: 6 to 8 in of compacted gravel base, 8 to 10 in for heavy vehicles. Gravel calculator
Tons are figured on the rolled thickness. The paver lays the mat about 25% thicker; the weight stays the same.
Prices & extras
For settling and waste. 0-15%.
Blank = typical 1.98 t/yd³
Typical US price. Edit to yours.
Added to bulk only.
A 50 by 12 ft driveway paved 2 in thick takes about 8.1 tons of hot-mix asphalt, so order 8.5 tons.
How to use the asphalt calculator
- Measure the paved area as a rectangle, circle or triangle, or type the square feet if you already know them. Add another area for each separate pad, turnaround or parking spot.
- Pick the project. A driveway for cars starts at 2 in and heavy vehicles or parking at 3 in. Type your own thickness if the paving contractor quoted a different one.
- Read the result: tons of hot-mix asphalt, the cubic yards behind it and a range, then the order line, rounded up to the next half ton.
- Under Prices & extras, change the extra percentage or the price per ton to match your quote.
- The box under the result adds the installed price per square foot and the stone base that goes under the asphalt.
How the asphalt calculator works
The calculator multiplies the area by the compacted thickness, turning inches into feet by dividing by 12, and divides the cubic feet by 27 to get cubic yards. It then adds 10 percent for edges and uneven ground. New York State DOT adds the same 10 percent to its estimated tonnage.
Hot-mix asphalt is sold by the ton, so the volume turns into weight at 1.98 tons per cubic yard. That figure is the highway departments’ rule: Indiana and Wisconsin both estimate 110 lb per square yard for each inch of compacted depth, and 110 times 36 divided by 2,000 is 1.98. The range runs from 1.96, the figure New York State DOT uses, to 2.09, the heaviest mix New York lists.
Tons are figured on the compacted, finished thickness. The paver lays the loose mat about 25 percent thicker, so a 2 in layer goes down at roughly 2.5 in, and the roller squeezes it back to 2 in. The mass in the truck does not change while that happens, so the tonnage needs no loose-to-compacted factor. Adding 25 percent to the tons would buy asphalt you never lay.
The order line rounds up to the next half ton. Plants sell by the ton and each sets its own minimum order: about 2 tons at the plant and in the cost guide checked here. Below the minimum, expect a short-load fee or a pickup, so ask yours before you order.
Pricing and what a contractor charges
The calculator starts the hot mix at $100 per ton, inside a $40 to $200 range. The sources do not agree: HomeGuide lists material at about $40 to $80, Bob Vila at $100 to $200, and a 2026 Texas county bid came in near $100 delivered. Type your supplier’s price.
A contractor’s price is per square foot and includes the stone base, the labor, the machines and the mix. A new driveway runs about $5 to $15 per square foot, and paving over an old driveway about $2 to $7. The box under the result multiplies your area by that price so you can compare a quote with the material alone.
What goes under the asphalt
Asphalt is only the top layer. A driveway for cars sits on 6 to 8 in of compacted gravel, and a driveway for heavy vehicles or a parking area sits on 8 to 10 in. Use the gravel calculator for the base and the cubic yards to tons converter to turn its volume into a delivery weight. Recycled asphalt millings have their own row in the converter and weigh less than new hot mix.
Thickness and coverage guide
A car driveway takes 2 to 3 in of asphalt on 6 to 8 in of stone base; heavy vehicles or parking take 3 to 4 in on 8 to 10 in. The last column is the published coverage of one ton; the calculator’s own line comes out a little higher because it uses 1.98 tons per cubic yard.
| Project | Asphalt | Stone base | Sq ft per ton |
|---|---|---|---|
| Driveway, cars | 2 to 3 in | 6 to 8 in | 80 at 2 in, 55 at 3 in |
| Heavy vehicles or parking | 3 to 4 in | 8 to 10 in | 55 at 3 in, 40 at 4 in |
Pavement design, mix design, sealcoat and striping are outside what a quantity calculator can answer. For a concrete drive or patio, use the concrete calculator, and for pavers the paver calculator.
Worked example
- Area: 50 ft × 12 ft = 600 sq ft
- Depth: 2 in ÷ 12 = 0.167 ft
- Volume: 600 sq ft × 0.167 ft = 100 cu ft
- Extra for settling: 100 cu ft × 1.10 = 110 cu ft
- Cubic yards: 110 ÷ 27 = 4.07 cu yd (3.11 m³)
- Weight: 4.07 cu yd × 1.98 tons per cu yd = 8.1 tons (7.3 tonnes)
- Order: round up to 8.5 tons
Questions people ask
How many tons of asphalt do I need?
Multiply the area in square feet by the compacted thickness in inches, divide by 12 for cubic feet, then by 27 for cubic yards, and multiply by about 1.98 tons per cubic yard. That is the 110 lb per square yard per inch rule that state highway departments use. Order about 10 percent more for edges and waste.
How much does a ton of asphalt cover?
About 80 square feet at 2 inches, 55 at 3 inches and 40 at 4 inches, by the usual price guides. The calculator works it out for your thickness and shows it under the order line; at 1.98 tons per cubic yard that is 82 square feet at 2 inches.
How thick should an asphalt driveway be?
2 to 3 inches of compacted asphalt over 6 to 8 inches of compacted stone for cars. For trucks, RVs or a parking area use 3 to 4 inches over an 8 to 10 inch base. The base matters as much as the asphalt: thin asphalt on a poor base cracks early.
Do I add extra tons because asphalt compacts?
No extra tons for compaction, but add about 10 percent for edges and waste. The paver lays the loose mat about 25 percent thicker than the finished layer, and the roller squeezes it down to your thickness, but the weight does not change. Tons are figured on the finished, compacted thickness.
How much does an asphalt driveway cost?
About $5 to $15 per square foot installed for a new driveway, and about $2 to $7 to pave over an old one. The hot mix alone is quoted at about $40 to $200 per ton depending on the region and who is asked; the calculator starts at $100 per ton.
How many tons is a cubic yard of asphalt?
About 1.98 tons for compacted hot-mix asphalt, inside a range of 1.96 to 2.09. Recycled asphalt millings are lighter and listed separately in the cubic yards to tons converter.