How to Read a Tape Measure

Tap any mark on a measuring tape to read it in inches.

Each inch on a US tape has 16 parts; longer lines mark bigger fractions.

Tap near a mark, then use Previous or Next mark to land on it.

3 5/8 in3.625 in · 92.075 mm10 sixteenths past 3

Practice is a picture quiz: the marked line is only in the drawing. If you cannot see it, the tape reader above reads every mark aloud with the arrow keys.

The drawing shows 2 in to 4 in of a US tape. The marked line is 10 sixteenths past 3 in: 3 5/8 in (3.625 in, 92.075 mm).

Tape measure marks: what each line means

Between two inch numbers, the longest line is the 1/2, then the 1/4s, the 1/8s and, shortest, the 1/16s. Each inch holds 16 equal spaces, so you count lines instead of guessing. Tap the drawing above to see any one of them as a fraction, a decimal and millimetres. Some tapes also mark 32nds; pick that scale above.

A few marks stand out. The “1F” at 12 in ends the first foot, and 2F, 3F and so on follow every 12 in. Many tapes print every 16 in in red (16, 32, 48), the usual spacing when you frame at 16 in on center. Black diamonds every 19.2 in space trusses and I-joists. The jump buttons under the drawing land on each of them.

Tape measure reading: the fraction at any mark

To read a tape measure in inches, find the last whole inch before the mark, count the sixteenths past it, then reduce the fraction. A mark 10 sixteenths past 3 in gives 10/16, which reduces to 5/8 when you divide both numbers by 2. Say it as “3 and 5/8 inches”: that is 3.625 in, or 92.075 mm.

Even counts always reduce: 2 sixteenths is 1/8, 4 is 1/4, 6 is 3/8 and 8 is 1/2. Odd counts stay as sixteenths. Counting is where mistakes creep in, so count back from the next inch line, or start from the 1/2 and 1/4 lines you already know and add or subtract the small marks. Layout work such as stair risers rewards that habit.

The Practice button asks about 10 random marks and tells you why each answer is right.

Marking a measurement: crow’s foot, burned inch, feet and inches

Mark with a small V, a crow’s foot, whose point sits on the exact line. A single dash can land on either side of the mark you meant, and the point of the V cannot.

If the hook is bent or loose, burn an inch: line up the 1 in mark with the edge, read the other end, then take 1 inch off. A reading of 23 in becomes 22 in.

Long readings are easier to check in feet and inches: 50 in is 4 ft 2 in, because 4 ft is 48 in. Write the number down before you cut.

Inside measurements: the sliding hook and the case length

The metal hook on the end slides about its own thickness, about 1/16 in on many tapes. That is on purpose: hooked over an edge it reads an outside measurement from the true zero, and pushed against a wall it reads an inside measurement from the true zero too.

For an inside measurement, butt the case against one wall, read the tape at the other wall and add the case length printed on the case. Never bend the tape into the corner. Tapes differ, so check your own hook and the length printed on your case.

Tape measure fractions chart: sixteenths, decimals and mm

To read a tape measure in fractions, learn the 16ths: each one is shown here as a decimal and in millimetres. Say the reduced fraction out loud.

FractionInchesmm
1/160.06251.588
1/80.1253.175
3/160.18754.763
1/40.256.35
5/160.31257.938
3/80.3759.525
7/160.437511.113
1/20.512.7
9/160.562514.288
5/80.62515.875
11/160.687517.463
3/40.7519.05
13/160.812520.638
7/80.87522.225
15/160.937523.813

Questions people ask

What are the black diamonds on a tape measure?

Marks every 19.2 in (19 3/16 in on some tapes) for spacing trusses and I-joists: five spaces make exactly 8 ft.

Why are 16, 32 and 48 red on a tape measure?

16 in is the usual stud spacing, so many tapes print every 16th inch in red. Three spaces make 48 in, the edge of a 4 ft sheet.

What is 5/8 on a tape measure?

10 sixteenths past the inch line: 0.625 in, or 15.875 mm, halfway between the 1/2 and 3/4 lines.

What are the numbers on a measuring tape?

The big numbers count whole inches. 12, 24 and 36 also carry 1F, 2F and 3F for feet, and many tapes print 16, 32 and 48 in red for stud spacing.

How do you read a metric tape measure?

10 mm make 1 cm: read the last numbered centimetre, then count the millimetre lines past it; the slightly longer middle line is 5 mm. 12 cm and 7 mm is 127 mm.

What is the smallest mark on a tape measure?

On most US tapes it is 1/16 in, the shortest line between two inch numbers. Some tapes mark 1/32 in; pick that scale above to see it. On the metric side the smallest line is 1 mm.

Related calculators