Units

Mortar Calculator

Bags of mortar mix, or cement, lime and sand, for block, brick, stone veneer and tuckpointing.

An 80 lb mortar mix bag lays about 12 blocks (8x8x16) or 35 bricks before waste: 100 blocks plus 10% = 10 bags.

Bag yields leave out waste and spills, so 10% is added to start. Change it to suit your job.

Optional. Adds a cost line for the bags.

Mortar mix · 80 lb

10bags

12 blocks per bag + 10% extra

Weight

800lb

About 7.1 cu ft of mixed mortar

Order 10 bags of 80 lb mortar mix for 100 blocks.
  • Wet mortar is caustic: the cement in it can burn skin and damage eyes. Wear nitrile gloves and eye protection, and if mortar gets in your eyes, rinse them with water for several minutes.
  • Type N suits most walls above ground; Type S suits load-bearing walls and work at or below grade. Your plans or local code decide for structural and retaining walls.

What one bag of mortar lays: blocks, bricks and stone veneer

Bags of mortar: blocks, bricks and veneer per bag, as the makers rate them before waste.
BagBlocks (8x8x16)BricksStone veneer, sq ft
Mortar mix 80 lb123510
Mortar mix 60 lb926-
Mortar mix 40 lb618-
Masonry cement 70 lb + 240 lb sand30144-
Stone veneer mortar 80 lb--13
Stone veneer mortar 50 lb--8

Makers' yields before waste. Quikrete rates its 80 lb bag at up to 13 blocks or 37 bricks; the calculator uses the lower figures.

Mortar types M, S, N and O: mix by volume and strength

Mortar types by mix and strength: parts of portland cement, hydrated lime and damp sand by volume, with the 28-day strength.
TypeCement : lime : sand28-day strength, psiWhere it goes
Type M1 : 1/4 : 3 3/42,500At or below grade: foundation and retaining walls
Type S1 : 1/2 : 4 1/21,800Above grade: load-bearing or reinforced walls
Type N1 : 1 : 6750Above grade: veneer, garden and non-load-bearing walls, chimneys; Interior walls
Type O1 : 2 : 9350Repointing old brick

Laying 100 concrete blocks (8x8x16) takes 10 bags of 80 lb mortar mix: 12 blocks per bag, plus 10% extra.

How to use the mortar calculator

The page returns whole bags of the size on the shelf from a block or brick count or a wall area: pick the job and type the count. Premixed mortar mix is the default and needs only water. Masonry cement with mason’s sand, and portland cement with hydrated lime and sand, are the two mixes you blend yourself. Stone veneer and tuckpointing use their own bag yields. The extra starts at 10% because makers’ yields leave out waste and spills (25% for tuckpointing); change it to suit the job. The metric toggle takes m² and mm.

How much mortar do I need for 100 blocks? 10 bags of 80 lb mix

100 concrete blocks take 10 bags of 80 lb mortar mix: 100 ÷ 12 blocks per bag = 8.33, plus 10% extra = 9.17, rounded up. Sakrete rates an 80 lb bag at 12 blocks (8x8x16) or 35 bricks, so 1,000 bricks with the same 10% take 32 bags. Count a wall’s blocks or bricks with the concrete block calculator or the brick calculator, then type the count here. Wet mortar is caustic: wear nitrile gloves and eye protection, and rinse your eyes with water for several minutes if it splashes in.

Mix it yourself: portland cement, lime and sand by volume

Type N mortar is 1 part portland cement, 1 part hydrated lime and 6 parts damp sand by volume, and one 94 lb bag of cement makes a batch that lays about 62 blocks or 300 bricks. Those counts come from CMHA’s estimating table and include nominal waste. Masonry cement is the shortcut: a 70 lb bag mixed with 240 lb of sand lays about 30 blocks or 144 bricks, which is 7 bags before waste, or 8 bags and 1,920 lb of sand per 1,000 bricks with 10% extra. Use damp, loose sand, 2 1/4 to 3 1/2 times the cement plus lime by volume; the sand calculator works out tons of sand from a volume. Lime comes in 50 lb bags of 1 1/4 cu ft, so the calculator rounds it up to whole bags.

Type N or Type S mortar: which one for your wall

Type N suits most walls above ground, veneer and chimneys; Type S suits load-bearing walls and work at or below grade. Type M is for foundation and retaining walls, and Type O for repointing old brick. Strength at 28 days runs from 2,500 psi for Type M down to 350 psi for Type O. Your plans or local code decide the type for structural and retaining walls. Sakrete sells its premixed Type S for block or stone above or below grade.

Stone veneer mortar: about 9 bags per 100 sq ft

100 sq ft of manufactured stone veneer takes 9 bags of 80 lb stone veneer mortar: Sakrete rates a bag at 13 sq ft, plus 10% extra. Its 50 lb bag covers 8 sq ft. Those yields are for setting and grouting stone 3/8 to 1/2 in thick and leave out waste and spills. A standard mortar mix also works, at Sakrete’s 10 sq ft per 80 lb bag, so you buy more bags.

Tuckpointing: rake joints 2 to 2 1/2 times their width

Rake old joints 2 to 2 1/2 times their width, about 1/2 to 1 in deep for most brick; a 150 sq ft brick wall with 3/8 in joints raked 3/4 in deep takes about 4 bags of 80 lb mortar with 25% extra. Grinding out old mortar makes silica dust: OSHA’s rule for tuckpointing grinders calls for a shroud with a dust collector and a respirator (APF 10, or APF 25 on jobs over 4 hours a shift). The calculator multiplies the joint length per sq ft (72 in for modular brick, 27 in for 8x16 block) by the joint width and depth, then divides by 0.71 cu ft per bag, the volume Quikrete gives its 80 lb veneer and pointing mortar. BIA adds 15 to 25 percent for waste, so read the bag count as an estimate. Match the old mortar and never use a stronger one: Type O for old soft brick, Type N for newer brick.

Why bags lay less than the wall’s mortar volume

A bag lays about half what the wall’s mortar volume suggests: Quikrete’s 144 bricks per 2.75 cu ft batch works out to 19.1 cu ft per 1,000 bricks, while BIA puts the mortar in the wall at 8.1 cu ft. So the calculator divides your count by the makers’ yield per bag. Dividing the wall’s mortar volume by the bag volume would under-buy by about half.

What the mortar estimate leaves out: thinset, stucco, grout

Tile thinset, patio mortar beds, stucco, core-fill grout and colored mortar are different products with their own coverage, so they are not counted here; the concrete block calculator covers core fill. Lay mortar only at 40 F or warmer, and keep it from freezing while it cures, as the bag says.

Worked example

  1. Blocks: 100
  2. Bags: 100 ÷ 12 blocks per 80 lb bag = 8.33
  3. With 10% extra: 8.33 × 1.10 = 9.17, round up to 10 bags
  4. Weight: 10 × 80 lb = 800 lb
  5. Mixed mortar: 10 × 0.71 cu ft = 7.1 cu ft

Questions people ask

How many 80 lb bags of mortar for 1,000 bricks?

32 bags at 35 bricks per bag plus 10% extra, or 30 at Quikrete's rating of up to 37. With masonry cement it is 7 bags of 70 lb, or 8 with 10% extra, and 1,920 lb of sand.

Can I use mortar mix for stone veneer?

Yes, at 10 sq ft per 80 lb bag: that is Sakrete's figure for its Type S mortar mix on cultured stone, against 13 sq ft for its stone veneer mortar, so you buy more bags.

How much sand goes with a bag of masonry cement?

240 lb, about 3 cu ft of damp mason's sand, per 70 lb bag. Quikrete says that batch makes about 2.75 cu ft of mortar.

How cold is too cold to lay mortar?

Below 40 F. Quikrete says not to use its masonry mortars under 40 F, and Sakrete wants the air, mix and wall between 40 and 90 F. Keep fresh mortar from freezing while it cures, for as long as the bag says.

Related calculators