Units

Sand Calculator

Yards, tons, bags and cost for paver, play, mason or fill sand.

1 cubic yard of paver sand weighs about 1.35 tons and covers 324 sq ft as a 1 in bedding layer under pavers.

Shape of the area

Paver bedding layer: 1-1.5 in deep

BETTER BUY

Bulk · by the ton

0.6tons

= 0.41 cu yd

Range 0.5–0.6 tons

$98

estimate, with delivery

$8.92 per cu ft

Bags · 0.5 cu ft

22bags

1,100 lb to carry

$110

estimate

$10.00 per cu ft

Order 1 ton of paver sand. Covers 120 sq ft at 1 in.

1 ton covers about 240 sq ft at 1 in.

Prices & extras

For settling and waste. 0-15%.

Blank = typical 1.35 t/yd³

Typical US price. Edit to yours.

Added to bulk only.

Per 0.5 cu ft bag

Polymeric sand for the joints

Uses the area above. Makers' coverage for 50 lb bags.

For 120 sq ft of pavers with narrow joints: 2 to 3 bags of 50 lb polymeric sand.

A 12 by 10 ft area at 1 in deep needs about 0.41 cubic yards of paver sand: about 0.6 tons, or 22 bags of 0.5 cu ft.

How to use the sand calculator

  1. Measure the area as a rectangle, circle or triangle, or type a square footage you already know. Add another area for each separate spot.
  2. Pick the project: paver bedding, a flagstone bed, a sandbox, play equipment, a pool base, a volleyball court or a thin lawn leveling pass. Each fills in a sourced typical depth you can change.
  3. Choose the sand. Each type has its own weight per cubic yard and its own uses, so the right one matters as much as the amount.
  4. Read the result: cubic yards, tons, 50 lb bags and an order line rounded to what a sand yard or store actually sells.
  5. For a paver patio, the polymeric sand box under the calculator counts the joint sand bags for the same area. Pick your joint width: a 3/8 inch joint takes about twice the sand of a 1/8 inch one.

How the sand calculator works

The volume is length times width times depth for a rectangle, or the matching formula for a circle or triangle, with the depth turned from inches into feet before multiplying. Dividing cubic feet by 27 gives cubic yards. Weight comes from multiplying cubic yards by the typical tons per cubic yard for the sand you picked, with its low and high figures shown as a range.

Sand weight swings more with water than with type. Bagged sand is dry; bulk sand from a yard usually arrives damp and weighs more for the same volume, so a load sold by the ton holds a little less sand than the dry math suggests. The range under the weight shows that spread.

Two adjustments come before the order line. An extra percentage covers settling and spillage: bedding sand is screeded loose and compacts once the pavers are set, so paver sand carries the most. Then the order line rounds up to the next half cubic yard or half ton, and bag counts round up to whole 50 lb bags. Fill sand is sold in bulk only.

Pick sand by job. Paver sand, which yards also call concrete sand, is coarse and drains, so it is the bedding layer under pavers and flagstone. Don’t bed pavers on mason or play sand: both are too fine and stay soft underfoot. Mason sand is finer and smoother, made for mortar, joints and the base under an above-ground pool liner. Play sand is washed and screened for sandboxes and play areas. Fill sand is the cheapest and least processed, for raising grades and filling holes.

Sand depth guide

Project Depth Sand to use
Paver bedding layer 1-1.5 in Paver sand
Flagstone setting bed 1-2 in Paver sand
Sandbox 6-12 in Play sand
Under play equipment 9-12 in Play sand
Above-ground pool base 2-3 in Mason sand
Volleyball court 12-18 in Washed sand
Lawn leveling pass 0.25-0.5 in Mason sand

Worked example

  1. Area: 12 ft × 10 ft = 120 sq ft
  2. Depth: 1 in ÷ 12 = 0.083 ft
  3. Volume: 120 sq ft × 0.083 ft = 10 cu ft
  4. Extra for settling: 10 cu ft × 1.10 = 11 cu ft
  5. Cubic yards: 11 ÷ 27 = 0.41 cu yd (0.31 m³)
  6. Weight: 0.41 cu yd × 1.35 tons per cu yd = 0.6 tons (0.5 tonnes)
  7. Order: round up to 1 ton, or 22 bags of 0.5 cu ft

Questions people ask

How much does a yard of sand weigh?

About 1.2 to 1.5 tons, with 1.35 tons a good planning figure for paver and mason sand and about 1.3 tons for play sand. Damp sand from a yard weighs more than dry bagged sand. A 50 lb bag holds about 0.5 cu ft.

How many 50 lb bags of sand are in a cubic yard?

A cubic yard is 27 cubic feet and a 50 lb bag holds about 0.5 cubic feet, so about 54 bags. Bulk is usually cheaper once you need a yard.

How much sand do I need under pavers?

About 1 inch of loose concrete sand, up to 1.5 inches. For the 12 by 10 ft patio in the example that is 0.41 cubic yards, about 0.6 tons or 22 bags of 50 lb, with 10 percent extra because the layer is screeded loose and settles.

How much sand do I need for a sandbox?

Fill a sandbox 6 to 12 inches deep, 8 inches typical, with washed play sand. Under swings and slides the safety guideline is at least 9 inches of loose sand, up to 12. Pick the Sandbox project above and type the size of your box.

How much does sand cost?

Bulk sand typically runs about $20 to $62 a ton for paver sand, $28 to $60 for play sand and $10 to $30 for fill sand, and a 50 lb bag costs about $4 to $7.50. Delivery adds $0 to $150, about $75 typical, so bags only win on small jobs.

How much polymeric sand do I need?

Makers rate a 50 lb bag at about 50 to 85 sq ft of pavers with narrow 1/8 to 1/4 inch joints, but Sakrete gives only 20 to 40 sq ft at about 3/8 inch, and Alliance 22 to 42 sq ft with wide 3/4 to 1-1/4 inch joints on larger pavers. Small pavers have more joint per square foot, so they sit at the low end. The box under the calculator works out the bags for your area and joint width.

Related calculators

Related guides