Units

Pool Volume Calculator

How many gallons and litres your pool holds, for every common pool shape.

A cubic foot holds 7.48 US gallons, so a 30 x 15 ft pool with a 5 ft average depth holds 16,830 gallons.

Measure the water, not the wall: from the water line to the floor.

Assumes the floor slopes evenly. If the deep end drops off suddenly, work out the shallow part and the deep part on their own and add them.

Water

16,830gallons

63,713 L · 63.7 m³

Volume

2,250cu ft

450 sq ft of water surface × 5 ft average depth

Your pool holds about 16,830 gallons (63,713 L).
  • Rectangle: length × width
  • 1 cu ft = 7.48 US gallons. Guides that multiply by 7.5 come out about 0.3% higher.

Above-ground pool sizes at 4 ft of water

Gallons depend on the water depth: type your own depth above. Shop charts for the same sizes differ because they assume other depths and shapes.

Round pools at 4 ft of water, US gallons.
Round poolGallons
12 ft3,384
15 ft5,287
18 ft7,614
21 ft10,363
24 ft13,535
27 ft17,131
30 ft21,149
Oval pools at 4 ft of water, US gallons.
Oval poolStraight sidesCurved all round
12 x 24 ft7,6926,768
15 x 30 ft12,01910,575
18 x 33 ft15,69213,958
18 x 40 ft19,46216,919
21 x 43 ft24,18621,220

A 30 by 15 ft pool that runs from 3 ft to 7 ft deep holds about 16,830 gallons: 2,250 cu ft of water, or 63,713 litres.

How to use the pool volume calculator

  1. Pick the pool’s shape. For an oval, look at the long sides: straight in the middle means “straight sides”, which is how most above-ground ovals are built; curved all the way along means “curved all round”. For a free-form pool, pick “Other shape” and type the water surface area from the plan.
  2. Type the sizes in feet, or switch to metres at the top. A kidney pool takes its length from end to end and the width across each rounded end, A and B.
  3. Pick the depth. For a pool with a shallow end and a deep end, type both and the calculator averages them. For a flat floor or an above-ground pool, pick one depth.
  4. Measure the water, not the wall: from the water line down to the floor.
  5. Read the gallons, litres and cubic feet. Share the link, copy the result or print it.

How many gallons are in my pool?

Work out the water surface in square feet, multiply by the average depth in feet, then multiply by 7.48. The shape decides the surface, and the table below lists the rule for each. To turn that into salt for a saltwater pool, take the gallons to the pool salt calculator. For chemical doses, use the pool chemical calculator and the product label.

How to calculate gallons in a pool

Water surface. Each shape has its own area rule, worked out in square feet. A rectangle is length times width. A round pool is π times the diameter squared, divided by 4. An oval with straight sides is a rectangle with a half circle at each end, and an oval that curves all the way round is an ellipse. A kidney pool uses the pool trade’s rule of thumb: 0.45 times the two end widths added together, times the length.

Average depth. With a shallow end and a deep end, the calculator adds the two depths and divides by 2. That is right when the floor slopes evenly from one end to the other. A pool that stays shallow for most of its length and then drops into a deep diving area holds less than that average suggests. For that pool, work out the shallow part and the deep part on their own and add the two.

Gallons and litres. The water surface times the average depth gives cubic feet. One cubic foot holds 7.48 US gallons, so the calculator multiplies by 7.48. Litres come from the same cubic feet, at 28.317 litres each. Sizes typed in metres are turned into feet first, so the gallons and the litres always describe the same water. Nothing is rounded until the result is shown.

Pool shape formulas

Shape Water surface Measure
Rectangle length × width Inside, at the water line
Round π × diameter² ÷ 4 Across the middle
Oval, straight sides width × (length − width) + π × width² ÷ 4 Longest and widest points
Oval, curved all round π ÷ 4 × length × width Longest and widest points
Kidney 0.45 × (A + B) × length End to end; across each rounded end
Free-form The area you type From the pool plan

Multiply the water surface by the average depth for cubic feet, then by 7.48 for US gallons.

Oval pools: straight sides or curved all round

Most above-ground ovals are built with straight side walls, held up by buttresses, and a half circle at each end. A true ellipse curves the whole way round. For the same length and width, the straight-sided oval holds more water, because its middle stays full width. That is why pool guides disagree on ovals: many use one shortcut multiplier that assumes an ellipse, and it comes out low for a straight-sided pool. This calculator works out both shapes exactly, so pick the one that matches your pool. If you are not sure, look along a long side: a straight wall means straight sides.

Above-ground pools

Use the water depth, not the wall height. Above-ground pools are filled to below the top of the wall, so a volume worked out from the wall height is too high. Measure from the water line to the floor in a few places, and type the average as one depth.

The table below the calculator lists common round and oval sizes at 4 ft of water, worked out with the same formulas. Size charts from pool shops and makers often give other numbers for the same pool, because each assumes its own water depth and oval shape. Your own measurement beats any chart.

What the pool volume figure leaves out: steps, benches, spas

Steps, benches, swim-outs and sun shelves are not subtracted, and a spa that spills into the pool is not added. Hopper and diving ends that drop off suddenly need the two-part method above. Fill time and the cost of the water are not worked out here.

Worked example

  1. Surface: 30 ft × 15 ft = 450 sq ft
  2. Average depth: (3 ft + 7 ft) ÷ 2 = 5 ft
  3. Volume: 450 sq ft × 5 ft = 2,250 cu ft
  4. Gallons: 2,250 cu ft × 7.48 = 16,830 US gallons
  5. Litres: 2,250 cu ft × 28.317 = 63,713 L, or 63.7 m³
  6. With the 7.5 shortcut: 2,250 cu ft × 7.5 = 16,875 gallons, about 0.3% more

Questions people ask

How many gallons are in my pool?

Multiply the water surface by the average depth to get cubic feet, then multiply by 7.48. A 30 x 15 ft pool that runs from 3 ft to 7 ft deep averages 5 ft, so it holds 2,250 cu ft of water, about 16,830 gallons.

How do I find the average depth of a pool with a shallow and a deep end?

Add the shallow and deep depths and divide by 2: 3 ft and 7 ft average 5 ft. That assumes the floor slopes evenly between them. If most of the pool is shallow and the deep end drops off suddenly, work out the shallow part and the deep part on their own and add them.

How many gallons is a 15 x 30 oval above-ground pool?

It depends on the water depth and on the sides. Most above-ground ovals have straight sides with a half circle at each end, and that shape holds more than an oval that curves all the way round. The table under the calculator shows both at 4 ft of water. For your own pool, pick the oval shape, type 30 and 15, and the water depth you measure.

How do I work out the gallons in a kidney-shaped pool?

The surface is about 0.45 x (A + B) x length, with the length measured from end to end and the width across each rounded end, A and B. Multiply that by the average depth for cubic feet, then by 7.48 for gallons. The 0.45 rule is an industry estimate, so treat the answer as close, not exact.

Why do some guides multiply by 7.5 and others by 7.48?

A cubic foot of water is 7.48 US gallons. 7.5 is a rounded shortcut that comes out about 0.3% high: the example pool reads 16,875 gallons with it instead of 16,830. For dosing chemicals the gap does not matter, but this calculator uses 7.48.

Should I use the wall height or the water depth?

The water depth. Measure from the water line down to the floor. Above-ground pools are filled below the top of the wall, so the wall height gives more gallons than the pool really holds.

Related calculators