Units

Pool Salt Calculator

Pounds of salt, bags to buy and the water to drain for a salt chlorine pool.

Salt (lb) = gallons x 8.34 x ppm raise / 1,000,000: 10,000 gallons from 0 to 3,200 ppm takes 267 lb, 7 bags of 40 lb.

Use the water in the pool, not the size on the box. The pool volume calculator works it out.

Picking one sets the target. You can still change it.

Test the water with a salt test first.

Hayward AquaRite: 2,700 to 3,400 ppm, 3,200 ideal.

Salt to add

275lb of salt

124.8 kg to raise 15,000 gallons from 1,000 to 3,200 ppm

Bags · 40 lb

7bags

40 lb bags: add 6 full bags and 35.2 lb of the 7th

Salt level

3,200ppm

Hayward AquaRite: 2,700 to 3,400 ppm, 3,200 ideal; all 7 bags would land near 3,240 ppm

Order 7 bags of 40 lb pool salt (275 lb to add).
  • Spread the salt around the pool with the pump running. Never pour it into the skimmer. Brush, let it circulate 24 hours, then test again.
  • Use plain pool salt, at least 99% sodium chloride: no iodized salt, no anti-caking additives, no rock salt.
  • On new or resurfaced plaster, wait until it has cured, as your chlorinator manual says.
  • This estimates the salt to add. Your chlorinator manual and the salt bag label come first.

Salt from zero to 3,200 ppm

Pool water (gallons)Salt (lb)40 lb bags to buy
5,0001334
10,0002677
15,00040011
20,00053414
25,00066717
30,00080121

A new pool starts near zero. If the water already holds salt, use the calculator above: it subtracts what is there. Whole bags can overshoot, so pour the full bags first and test.

A 15,000 gallon pool at 1,000 ppm needs 275 lb of salt to reach 3,200 ppm: buy 7 bags of 40 lb.

How to use the pool salt calculator

  1. Type the water in the pool, in gallons or litres. Use the water in the pool, not the size on the box. The pool volume calculator works it out from the shape and depth.
  2. Test the water with a salt test strip or meter, and type the result as the current level in ppm.
  3. Pick your chlorinator. Hayward AquaRite, Pentair IntelliChlor and Intex Saltwater System set the target to the maker’s ideal. For any other cell, pick “Other” and type the level from its manual. Some cells, including Jandy, show grams per liter: multiply by 1,000 to get ppm.
  4. Pick the bag you can buy: 40 lb, 20 kg, 25 kg, or type your own weight.
  5. Read the three tags: pounds of salt, bags to buy, and the level you land at. Add the salt the way the lines under the result say.

This estimates the salt to add. Your chlorinator manual and the salt bag label come first. For chlorine and pH doses, use the pool chemical calculator.

How the pool salt calculator works

Pounds of salt. A gallon of water weighs about 8.34 lb, and one ppm is one part in a million. So the salt to add is the gallons times 8.34 times the ppm you need to raise, divided by 1,000,000. The result also shows kilograms. A litre input is turned into gallons first, by dividing by 3.785411784.

Bags. The pounds are divided by the bag weight and rounded up. The result also shows how many bags are full and how much is left for the last one, because pouring every bag can overshoot the target. One bag raises the level by the same amount each time: the bag weight divided by the pounds that make one ppm in your pool.

The level you land at. The tag shows where all the bags you buy would leave the water, to the nearest 10 ppm. If that is above the top of your chlorinator’s range, a warning asks you to add the full bags and the partial bag, then test after 24 hours.

Too much salt. If the current level is above the target, nothing is added. The calculator shows the share of water to drain: the current level minus the target, divided by the current level. This assumes the fresh water you refill with has almost no salt. Drain only part of the pool: a fully drained pool can damage its liner or shell. Many towns bar salty or chlorinated pool water from storm drains, so ask your city or county where it may go.

The maker’s range. The ranges come from the chlorinator makers’ own manuals, not from a health code. The target can be any value from 1,000 to 5,000 ppm. A target outside the maker’s range is allowed, with a note.

Adding the salt

Spread the salt around the edge of the pool with the pump running. Never pour it into the skimmer. Brush it so it dissolves, let the water circulate for 24 hours, then test again before you add more. Use plain pool salt at least 99 percent pure. On new or resurfaced plaster, wait until it has cured, as your chlorinator manual says.

What the salt estimate does not know: fill-water salt, chlorine, pH

It does not set a chlorine, stabilizer or pH dose, and it does not add the cost of the salt. It does not know how much salt your fill water already holds. The Intex tables use only part of the nameplate volume of the pool, so enter the real water volume. Salt is lost to splash-out, backwash and overflow after rain, not to evaporation.

Worked example

  1. Salt to add: 15,000 gal × 8.34 lb × (3,200 − 1,000 ppm) ÷ 1,000,000 = 275.22 lb (124.8 kg)
  2. Bags: 275.22 lb ÷ 40 lb = 6.88, round up to 7 bags
  3. Full bags: 6, and 35.2 lb in the last one
  4. One bag adds: 40 lb ÷ (15,000 gal × 8.34 ÷ 1,000,000) = 319.7 ppm
  5. Pouring every bag: 1,000 + 7 × 319.7 = 3,238 ppm, about 3,240

Questions people ask

How much salt do I add to a 15,000 gallon pool?

From 1,000 ppm up to 3,200 ppm, the example above needs 275 lb: 15,000 gallons x 8.34 lb x the ppm raise, divided by 1,000,000. From a fresh fill at 0 ppm the same pool needs 400 lb.

How many 40 lb bags of salt is that?

Divide the pounds by 40 and round up. One 40 lb bag adds about 480 ppm to 10,000 gallons, and about 400 ppm to 12,000 gallons, so a bigger pool needs more bags for the same raise. Pour the full bags first, then only part of the last one.

What salt level does my chlorinator need?

Hayward AquaRite asks for 2,700 to 3,400 ppm with 3,200 ideal. Pentair IntelliChlor asks for 3,000 to 3,500 ppm, and its guide gives 3,400 as the ideal. The Intex Saltwater System asks for 2,500 to 3,500 ppm with 3,000 ideal. For any other cell, type the target from its manual.

What do I do if the salt level is too high?

From 4,000 ppm down to 3,200 ppm you drain 20 percent of the pool. Salt only leaves with water, and evaporation does not help, so drain part of the pool and refill with fresh water. The share to drain is the current level minus the target, divided by the current level. Then test again.

What kind of salt should I use?

Plain pool salt that is at least 99 percent sodium chloride. Skip iodized salt, anti-caking additives and rock salt. Water-conditioning pellets also work but dissolve more slowly.

How long before I test the water again?

Spread the salt around the pool with the pump running, brush it around, let the water circulate for 24 hours, then test. Never pour salt into the skimmer.

Related calculators