Units

Pool Chemical Calculator

How much chlorine, shock, acid, baking soda, calcium or stabilizer to add.

Raising chlorine 1 ppm in 10,000 gallons takes about 10.2 fl oz of 12.5% liquid chlorine or 1.8 oz of 73% cal-hypo. Shocking takes far more: read the label.

Use the water in the pool, not the size on the box. The pool volume calculator works it out.

Use a fresh jug: liquid chlorine loses strength with heat and age.

Optional: shows Trouble Free Pool's minimum and shock levels.

Add

46.1fl oz

0.36 gal of liquid chlorine 12.5% raises 15,000 gallons from 1 to 4 ppm

Per gallon

8.3ppm per gallon

What one gallon of this product adds to your pool. Pour it slowly into the deep end with the pump running.

Also adds

Only a littlesalt

Liquid chlorine adds no stabilizer or calcium.

Trouble Free Pool at CYA 30: keep free chlorine at 2 ppm or more; its shock (SLAM) level is 12 ppm.

Add 46.1 fl oz of liquid chlorine 12.5%, then test again.

Before you pour

  • This estimates amounts. The product label comes first.
  • Add the chemical to the pool water, never water to the chemical, and never mix chemicals together. Chlorine and acid give off toxic gas.
  • Pump running, swimmers out. Add one chemical at a time and test again before the next.

Chlorine for 1 ppm in 10,000 gallons

Fresh, full-strength product. Liquids are fluid ounces; granules and tablets are ounces by weight.

Product and strengthAmountAlso adds, per ppm
Liquid chlorine 12.5%10.24 fl ozA little salt
Liquid chlorine 10%12.80 fl ozA little salt
Household bleach 6% (plain, unscented)21.33 fl ozA little salt
Cal-hypo shock 73%1.83 oz0.71 ppm calcium
Cal-hypo shock 65%2.05 oz0.71 ppm calcium
Dichlor 56%2.38 oz0.91 ppm CYA
Dichlor 62%2.15 oz0.91 ppm CYA
Trichlor 90%1.48 oz0.61 ppm CYA

Balance chemicals in 10,000 gallons

JobChemicalAmount
Raise alkalinity 10 ppmBaking soda (sodium bicarbonate)1.4 lb
Raise pH 0.1Soda ash (sodium carbonate, pH up)3 oz
Lower alkalinity 10 ppmMuriatic acid 31.45%25.6 fl oz
Lower alkalinity 10 ppmHalf-strength muriatic acid (14.5% to 15.7%)51.2 fl oz
Lower alkalinity 10 ppmDry acid (sodium bisulfate)2.1 lb
Raise calcium 10 ppmCalcium chloride 100%0.925 lb
Raise calcium 10 ppmCalcium chloride 77%1.2 lb
Raise CYA 10 ppmStabilizer (cyanuric acid, granular)13.35 oz

A 15,000 gallon pool takes 46.1 fl oz (0.36 gal) of liquid chlorine 12.5% to raise free chlorine from 1 to 4 ppm.

This estimates amounts. The product label comes first.

How to use the pool chemical calculator

  1. Test the water first: free chlorine, pH, total alkalinity, calcium hardness and stabilizer (CYA).
  2. Pick what to adjust. Switching keeps your pool water.
  3. Type the water in the pool, in gallons or litres. Use the water actually in it, not the size printed on the box. If you do not know it, the pool volume calculator works it out. Salt-cell pool? Start with the pool salt calculator.
  4. Type your reading now and the target. For chlorine, pick the product and check the strength on its label; add your CYA reading to see Trouble Free Pool’s minimum and shock levels.
  5. Read the three tags, then the lines under them. Add the chemical in steps, test again, and only then add more.

How the pool chemical calculator works

Liquid chlorine. The percent on a jug of pool chlorine is a trade percent: grams of chlorine per 100 mL. That makes the maths short: fluid ounces = 0.0128 × gallons × ppm ÷ strength. One gallon of 12.5% liquid in 10,000 gallons adds 12.5 ppm, which is how PHTA puts it. Keep chlorine away from acid: together they give off toxic gas. Liquid chlorine loses strength with heat and age, so the answer assumes a fresh jug.

Granules and tablets. Cal-hypo, dichlor and trichlor are weighed, so the maths uses the weight of water, 8.34 lb a gallon: pounds = gallons × ppm × 8.34 ÷ 1,000,000 ÷ the strength as a decimal. Their ounces are ounces by weight, not fluid ounces.

What else chlorine adds. Trichlor leaves about 0.607 ppm of stabilizer for every ppm of chlorine, dichlor about 0.91, and cal-hypo about 0.706 ppm of calcium. Liquid chlorine and plain bleach add only a little salt. Stabilizer and calcium build up over a season and only come down when you replace water, so the result shows what each dose leaves behind.

Shock and stabilizer. Stabilizer protects chlorine from sunlight but also slows it down, so the more CYA in the water, the more chlorine it takes to do the same work. Trouble Free Pool keeps free chlorine at 7.5% of the CYA level or more, and its shock (SLAM) chart runs from CYA 20 to 100. The calculator reads between the chart’s rows. Pool owners use it; no health code requires it. Keep swimmers out until free chlorine is 4 ppm or less.

pH. Soda ash raises pH: about 3 oz for each tenth of a pH unit in 10,000 gallons, and it lifts alkalinity a little too. Acid lowers pH, but how far a dose moves it depends on your alkalinity and stabilizer, so the calculator gives a range: the acid that removes 1.6 to 2.5 ppm of alkalinity per tenth. Start with a third of the low end, run the pump for 30 minutes and test.

Alkalinity. Baking soda raises it: 1.4 lb per 10 ppm in 10,000 gallons, no more than 20 ppm at a time. Acid lowers it: 25.6 fl oz of full-strength 31.45% muriatic acid per 10 ppm in 10,000 gallons, twice that of half-strength acid (about 15%), or 2.1 lb of dry acid. Wear eye protection with acid. Each dose stays at or under 1 quart of full-strength acid per 10,000 gallons. Expect pH to fall as well.

Calcium and stabilizer up. Calcium chloride takes 0.925 lb per 10 ppm in 10,000 gallons at 100%, or 1.2 lb for the 77% kind. Granular stabilizer takes about 13.35 oz per 10 ppm. Liquid stabilizer differs by brand: follow its bottle.

Down by draining. Calcium and stabilizer leave only with water. The share to drain is the drop you want divided by the reading minus your fill water’s level. With fill water at 0, going from 100 to 50 means draining half. If your tap water already reads at or above the target, draining cannot get there, and the calculator says so.

Ranges, for context only

Public pool codes (the CDC Model Aquatic Health Code and Oregon’s rules) ask for free chlorine of at least 1 ppm, or 2 with stabilizer, pH from 7.0 to 7.8 and stabilizer at or under 90 ppm; a public pool closes above 10 ppm of chlorine while people swim. Swim University suggests alkalinity of 80 to 120 ppm, calcium of 175 to 225 for vinyl and fiberglass or 200 to 275 for plaster, and stabilizer of 30 to 50. These numbers show up as warnings next to your result, not as the answer.

Before you pour

Read the label: it comes first, and some shock labels say not to pre-dissolve. Add the chemical to the pool water, never water to the chemical, and never mix two chemicals together. Keep the pump running and swimmers out, add one chemical at a time, and test before the next. Pour acid slowly in front of a return jet, never into the skimmer, and wear eye protection. When both need work, adjust alkalinity before pH.

Worked example

  1. Chlorine to add: 4 ppm − 1 ppm = 3 ppm
  2. Liquid strength is grams of chlorine per 100 mL, so 128 fl oz per gallon ÷ 10,000 = 0.0128 fl oz per gallon of pool, per ppm, at 1%
  3. 0.0128 × 15,000 gal × 3 ppm ÷ 12.5 = 46.08 fl oz, about 46.1 fl oz
  4. In gallons: 46.08 fl oz ÷ 128 = 0.36 gal
  5. One gallon adds 10,000 × 12.5 ÷ 15,000 = 8.33 ppm
  6. Trouble Free Pool at CYA 30: minimum 7.5% × 30 = 2.25, about 2 ppm; shock (SLAM) 12 ppm from its chart
  7. Liquid chlorine adds no stabilizer or calcium, only a little salt

Questions people ask

How much liquid chlorine raises a pool 1 ppm?

In 10,000 gallons, about 10.24 fl oz of 12.5% liquid chlorine or 12.8 fl oz of 10%. Scale it to your pool: twice the water takes twice the chlorine. A full gallon of 12.5% adds 12.5 ppm to 10,000 gallons (PHTA).

What is pool shock, and how much do I use?

One pound of 65% cal-hypo adds about 7.8 ppm to 10,000 gallons (PHTA), and every shock label gives its own dose. Shock is a big dose of chlorine, often cal-hypo granules sold by the pound, used to kill algae and bacteria. To clear algae, Trouble Free Pool raises chlorine to a level set by your stabilizer: at CYA 30 its chart says 12 ppm, at CYA 50 it says 20.

Can I use household bleach instead of pool chlorine?

Yes, if it is plain, unscented bleach with nothing added. It is the same chemical as pool liquid chlorine, just weaker, usually 6%, so it takes about twice as much as 12.5% liquid. Skip splash-less, scented and fabric-protection bleach (TFP).

How much muriatic acid can I add at one time?

The Indiana pool guide says no more than 1 quart per 10,000 gallons at a time, then circulate and test before the next dose. The calculator splits a large alkalinity drop into doses that size and gives the first dose for pH as a third of the low estimate.

How much water do I drain to lower stabilizer (CYA)?

From 100 to 50 ppm with fill water at 0, you drain half the pool. The share to drain is the drop you want divided by the reading minus your fill water's level. Drain part of the water and refill; draining a pool fully can damage the liner or shell.

How long after shocking can we swim?

Chlorine labels say to stay out until free chlorine is back down to 4 ppm or less, so test before anyone gets in. Free chlorine falls as sunlight and swimmers use it up, so a high reading comes down on its own: test again the next day.

Related calculators