Roofing Calculator
Shingle bundles, squares, parts and cost for a gable or hip roof.
A 6/12 roof is 1.118 times its footprint, so 1,000 sq ft of roof footprint (overhangs included) takes about 34 bundles at 33.3 sq ft a bundle, before waste.
The ridge runs along the house length.
6 in of rise per 12 in of run: a 26.6° slope.
Past the wall, measured level.
IKO: 10 to 15%; This Old House adds 15%.
10 squares a roll, bought for the squares with waste. A square is 100 sq ft.
Cold climates. 3 ft wide rolls, run up from the eaves.
Section
Installed: about $9,241 ($6,011 to $12,021) for 15.03 squares.
- Section: 40 × 30 ft
- Roof: gable, 6/12 pitch, 12 in overhang, 10% waste
- Shingles: 33.3 sq ft a bundle, architectural
- Starter: OC Starter Strip Plus; ridge cap 25 ft a bundle; 4 nails a shingle
- Underlayment: synthetic; ice barrier along the eaves
Parts list
- Starter strip: 2 bundles (155.6 ft of eaves and rakes)
- Ridge cap: 2 bundles (42 ft of ridge)
- Drip edge: 16 pieces of 10 ft
- Ice barrier: 3 rolls (2 courses, 47 in up the slope)
- Nails: about 4,166 (4 per shingle)
- Ice barrier: the IRC wants it to reach 24 in inside the warm wall, measured level; check your local building code.
- Nails: 6 per shingle above 20:12 or in high wind zones; follow the bundle label and check your local building code.
This estimates quantities, not structural design or code compliance. Check your local building code.
Prices & extras
Owens Corning Starter Strip Plus: 105 ft a bundle, along the eaves and rakes.
GAF Seal-A-Ridge: 25 ft a bundle, for the ridge and any hips.
Follow the bundle label for your wind zone.
Check the label: OC Duration 32.8, IKO Marathon 3-tab 32.3.
Installed, 2026: $400 to $800 a square (100 sq ft).
Optional: the shelf price of one bundle.
Roof pitch factors
Multiply the footprint, overhang included, by the factor to get the roof area. The last column is the bundles for a 1,000 sq ft footprint at 33.3 sq ft a bundle, before waste.
| Pitch | Angle | Factor | Bundles |
|---|---|---|---|
| 2/12 | 9.5° | 1.014 | 31 |
| 3/12 | 14° | 1.031 | 31 |
| 4/12 | 18.4° | 1.054 | 32 |
| 5/12 | 22.6° | 1.083 | 33 |
| 6/12 | 26.6° | 1.118 | 34 |
| 7/12 | 30.3° | 1.158 | 35 |
| 8/12 | 33.7° | 1.202 | 37 |
| 9/12 | 36.9° | 1.250 | 38 |
| 10/12 | 39.8° | 1.302 | 40 |
| 11/12 | 42.5° | 1.357 | 41 |
| 12/12 | 45° | 1.414 | 43 |
| 14/12 | 49.4° | 1.537 | 47 |
| 16/12 | 53.1° | 1.667 | 51 |
| 18/12 | 56.3° | 1.803 | 55 |
A 40 by 30 ft house with a 6/12 gable roof and 12 in overhangs takes about 50 bundles of shingles: 15.03 squares of roof plus 10% waste.
How to use the roofing calculator
- Type the house length and width in feet, outside wall to outside wall. The ridge of a gable roof runs along the length. For an L-shaped house, add a section for each rectangle. For a roof you have already measured, pick Area and type its sloped area.
- Pick the roof shape and the pitch. Pitch is the rise in inches over 12 in of run, so a 6/12 roof climbs 6 in every foot. Not sure of yours? The roof pitch calculator finds it from a level and a tape.
- Type the overhang, measured level out from the wall. The calculator adds it to every side.
- Pick the underlayment and say whether you need ice and water barrier along the eaves.
- Open Prices & extras for the starter strip, the ridge cap, the nails, the bundle size on your label, the shingle type for the cost and your price per bundle.
- Read the order line and the parts list, or print the slip.
Falling is the main danger in roof work. Wear a harness tied to a solid anchor and set the ladder properly, or hire a roofer. OSHA requires fall protection for roofers at work 6 feet or more above a lower level.
How the roofing calculator works
Roof area. Each side gets the overhang, so a 40 by 30 ft house with 12 in overhangs has a 42 by 32 ft footprint. A sloped roof is bigger than its footprint by the pitch factor: the square root of 1 plus the rise over 12, squared, which is Pythagoras on a 12 in run. A hip roof with the same pitch on all four sides has the same area as a gable roof on the same footprint. A section typed as an area is used as it is, with no pitch or overhang added.
Squares and bundles. Squares are the roof area divided by 100. Waste goes on the squares, then the bundles are the squares times 100, divided by what one bundle covers, rounded up once at the end. At 33.3 sq ft a bundle, three bundles cover just under a square, so a large roof can need a bundle more than three per square.
Edges. A gable roof has eaves along both long sides and four rake edges, two at each gable end, each running from the eave up to the ridge. A hip roof has eaves all the way around, a shorter ridge and four hips. Starter strip and drip edge run along the eaves and the rakes. Drip edge comes in 10 ft pieces that lap 2 in, so each piece adds a little under 10 ft. Ridge cap covers the ridge and the hips.
Underlayment. Rolls are counted on the squares with waste, the way This Old House buys them. Synthetic rolls cover 10 squares, #15 felt 4 and #30 felt 2. Below 4/12 the IRC calls for a double layer, so the rolls are doubled.
Ice and water barrier. It has to reach 24 in inside the warm wall, measured level. The calculator adds the overhang, a 6 in wall and the 24 in, multiplies by the pitch factor to get the width up the slope, and lays 36 in courses along the eaves. A roll is 66.7 ft long. Laps between courses, valleys and rakes are not counted.
Nails and cost. Nails are the squares to buy times 63 shingles times 4 or 6 nails. The installed cost is the roof squares, without waste, times a 2026 price per square for the shingle type.
What roofing parts come in
| Part | Sold as |
|---|---|
| Architectural shingles | about 33.3 sq ft a bundle, 3 bundles a square |
| Starter strip | 105 ft a bundle (Owens Corning), 120.33 ft (GAF) |
| Ridge cap | 20 to 36.5 ft a bundle |
| Drip edge | 10 ft pieces, lapped 2 in |
| Synthetic underlayment | 10 squares a roll |
| #15 felt | 4 squares a roll |
| #30 felt | 2 squares a roll |
| Ice and water barrier | 3 ft by 66.7 ft, 200 sq ft a roll |
| Installed, architectural | $400 to $800 a square |
What the roofing estimate leaves out: valleys, flashing, vents, tear-off
This page counts materials, and your local building code decides what is allowed. Shingles need a slope of 2:12 or more, and the calculator refuses anything flatter. Valleys, flashing, vents, skylights, chimneys, tearing off old layers, sheathing, metal roofing and snow loads are not counted. Attic insulation is not counted either: the insulation calculator gives the bags and depth for the attic floor. Measure a cut-up roof in sections and add more waste.
Worked example
- Footprint with overhang: (40 ft + 2 × 12 in) × (30 ft + 2 × 12 in) = 42 ft × 32 ft = 1,344 sq ft
- Pitch factor: √(1 + (6 ÷ 12)²) = 1.118, a 26.57° slope
- Roof area: 1,344 sq ft × 1.118 = 1,502.64 sq ft = 15.03 squares
- To buy: 15.03 squares × 1.10 = 16.53 squares
- Bundles: 16.53 squares × 100 ÷ 33.3 sq ft = 49.64, round up to 50 bundles
- Edges: eaves 2 × 42 ft = 84 ft; rakes 4 × 16 ft × 1.118 = 71.55 ft; ridge 42 ft
- Starter strip: 155.55 ft ÷ 105 ft a bundle = 1.48, round up to 2 bundles
- Ridge cap: 42 ft ÷ 25 ft a bundle = 1.68, round up to 2 bundles
- Drip edge: 155.55 ft ÷ 9.83 ft (a 10 ft piece less its 2 in lap) = 15.82, round up to 16 pieces
- Underlayment: 16.53 squares ÷ 10 squares a roll = 1.65, round up to 2 rolls
- Ice barrier: (12 in overhang + 6 in wall + 24 in) × 1.118 = 46.96 in up the slope, 2 courses of 36 in; 2 × 84 ft ÷ 66.7 ft a roll = 2.52, round up to 3 rolls
- Nails: 16.53 squares × 63 shingles × 4 nails = 4,165.3, round up to 4,166
- Installed cost: 15.03 squares × $615 = $9,241 ($400 to $800 a square: $6,011 to $12,021)
Questions people ask
How many bundles of shingles are in a square?
Three, for most architectural and 3-tab shingles. A square is 100 sq ft of roof and a bundle covers about 33.3 sq ft: GAF Timberline HDZ lists 33.33, IKO Cambridge 33.3 and Owens Corning Duration 32.8. Some lines cover less, so read the bundle label and type its figure under Prices & extras.
How much waste should I add for shingles?
IKO gives about 10 to 15 percent as a general range, and This Old House adds 15 percent to the squares. The calculator starts a gable roof at 10 percent and a hip roof at 15, because hips take more cuts. Valleys and dormers push it higher; the field takes up to 30.
How do I find the roof area from the house size?
Add the overhang to each side of the house, multiply the length by the width, then multiply by the pitch factor: 1.118 for a 6/12 roof, 1.202 for 8/12 and 1.414 for 12/12. Divide by 100 for squares. A 40 by 30 ft house with 12 in overhangs and a 6/12 roof has about 1,503 sq ft of roof, or 15 squares.
How many nails go in each shingle?
At least four, says the IRC, and six above a 20:12 slope or in high wind zones. A square holds 63 standard shingles, so that is 252 nails a square with four, or 378 with six. IKO counts about 240 and 360 for its larger shingle. Follow the bundle label for your area.
How far up the roof does ice and water shield go?
The IRC wants it to reach at least 24 in inside the exterior wall, measured level. With a 12 in overhang and a 2x6 wall that is 47 in up a 6/12 roof, so one 36 in wide roll is not enough and you lay two courses. Many areas do not require it at all, so check your local building code.
How many bundles of ridge cap do I need?
Divide the ridge length, plus the hips on a hip roof, by the linear feet one bundle covers: GAF Seal-A-Ridge covers 25, Owens Corning ProEdge 33 and IKO Hip & Ridge 12 covers 36.5. The 40 by 30 ft example has a 42 ft ridge, so 2 bundles of 25 ft.