Units

Plywood Calculator

Sheets of plywood or OSB for a subfloor, walls or roof sheathing.

A 4 x 8 sheet covers 32 sq ft, so a 12 x 16 ft floor (192 sq ft) plus 10% waste takes 7 sheets.

How you measure it

Length × width of each floor area; a stairwell goes in Openings.

32 sq ft a sheet.

6/12 rises 6 in per foot: 26.6°, 1.118 × the footprint.

Eaves and rakes past the wall, added on every side.

Optional: area you won't cover (big doors, a stairwell, a skylight).

10% covers cuts and offcuts on most jobs; add more for hips, valleys and angled walls.

Plywood sheets

7sheets

4 × 8 ft · 6 with no waste

Area

192sq ft

211.2 sq ft to buy with 10% waste

Other sizes

4 × 9: 6 · 4 × 10: 6

Same area and waste in the other sizes

Order 7 sheets, 4 × 8 ft plywood or OSB.
  • One layer under the finish floor: 19/32 in (5/8 nominal) tongue and groove for joists 16 or 19.2 in apart, 23/32 in (3/4 nominal) for 24 in. Check your local code and the panel's stamp.
  • Run the long side across the joists or rafters, land end joints on supports and stagger them; leave a 1/8 in gap at edges and ends (APA).

This estimates sheets, not structural design or code compliance. Check your local building code.

Prices & extras

Optional: your store's price.

Sheets for common floors

4 × 8 ft sheets with 10% waste, one layer, no openings.

FloorSq ftSheets
8 × 8 ft643
10 × 12 ft1205
12 × 16 ft1927
16 × 20 ft32011
24 × 24 ft57620

A 16 by 12 ft floor needs about 7 sheets of 4 × 8 ft plywood or OSB: 192 sq ft plus 10% waste.

How to use the plywood calculator

  1. Pick what you are covering: a floor or subfloor, walls, or a roof. The pitch and overhang fields show only for a roof.
  2. Pick the sheet size. A 4 by 8 ft sheet is the common one; 4 by 9 ft and 4 by 10 ft sheets are made for taller walls and are in the list too.
  3. Type each section of the job. A floor is length by width. A wall is its length by its height, with walls added end to end, and each gable is a triangle with a base and a height. If you already know the area, pick Area and type it.
  4. For a roof, type the house footprint without the overhang, then the pitch and the overhang. The calculator adds both for you.
  5. Type the area you will not cover under Openings, if you want to leave it out: a stairwell, a big door, a skylight.
  6. Leave waste at 10 percent or change it. Under Prices & extras, type your store’s price per sheet to get a cost.
  7. Read the sheet count, the count in the other two sizes, and the order line.

How the plywood calculator works

Area. A rectangle is length times width and a triangle is half the base times the height. A section typed as an area is used as it is. The rows are added up, then the openings come off.

Roof. Each rectangle is the house footprint. The calculator adds the overhang to every side, then multiplies by the pitch factor, the square root of 1 plus the rise over 12, squared. That is Pythagoras on a 12 in run. A triangle gets the factor but no overhang, and an area you typed is taken as it is, because a measured roof area is already sloped. The roofing calculator uses the same rule, so the same house gives the same roof area on both pages.

Waste and rounding. The net area times 1 plus the waste, divided by the area of one sheet, rounded up once at the end. The cuts and offcuts of a typical job are covered by 10 percent; hips, valleys and angled walls need more. The count in the other sizes uses the same area and the same waste.

What is not counted. Sheet weight, nails and clips, the width lost to a tongue and groove edge, and any cutting layout. The notes under the result give the thickness for the job and how to lay the sheets. The sheet count does not depend on them.

Sheet sizes and the notes under the result

Sheet Area Used for
4 x 8 ft 32 sq ft floors, roofs and most walls
4 x 9 ft 36 sq ft taller walls
4 x 10 ft 40 sq ft tall walls, from one maker’s spec

Many mills cut panels slightly under their nominal size, and the calculator still uses the full 32, 36 or 40 sq ft. The notes ask for a 1/8 in gap at edges and ends, which APA recommends so wet panels can swell. The thickness lines come from the IRC span tables and the APA floor guide, with one row per job and two spacings each. They do not know your snow or wind load.

What the plywood count leaves out: thickness, framing, nails

This estimates sheets, not structural design or code compliance. Check your local building code. The calculator does not pick a thickness from a span table, size joists or rafters, count the studs, or count a ceiling. Insulation between the joists: use the insulation calculator. For an accent wall backer under boards and battens, see the board and batten calculator. For shingles, underlayment and drip edge on the same roof, use the roofing calculator.

Worked example

  1. Area: 16 ft × 12 ft = 192 sq ft
  2. Area to cover: 192 sq ft
  3. To buy: 192 sq ft × 1.10 = 211.2 sq ft
  4. Sheets: 211.2 ÷ 32 sq ft a 4 × 8 ft sheet = 6.6, round up to 7 sheets

Questions people ask

How many sheets of plywood do I need?

Find the area to cover, divide by the area of one sheet, add about 10 percent for cuts and offcuts, and round up once at the end. A 4 by 8 ft panel is 32 sq ft. Fine Homebuilding, Hunker and iCEV teach the same steps.

How thick should plywood subfloor be?

For a single layer under the finish floor, the APA sturd-i-floor rows call for 19/32 in (5/8 nominal) tongue and groove on joists 16 in apart and 23/32 in (3/4 nominal) on joists 24 in apart. The IRC's 7/16 in row for 16 in joists assumes a separate underlayment layer on top. Check your local code and the panel's stamp.

How thick should roof sheathing be?

The IRC table for roof sheathing lists 3/8 in (24/0) panels for rafters or trusses up to 20 in apart without edge support, and 7/16 in (24/16) for 24 in. With edge support such as panel edge clips, 3/8 in spans 24 in. Heavier snow and wind loads can need more, so check your local code.

Why leave a 1/8 inch gap between sheets?

Panels swell a little with moisture, and APA recommends a 1/8 in space at edges and ends so they do not buckle. It is a recommendation, not a code rule, and some panel makers print their own spacing on the panel.

Should I use plywood or OSB?

The IRC span table covers all wood structural panels by their span rating, plywood and OSB alike, so the same rating gives the same span. NRCA prefers plywood for roof decks because OSB is more subject to swelling, ridging and fasteners backing out when it gets wet.

Which way do the sheets run?

On floors and roofs, run the long side across the joists or rafters, put end joints over a support and stagger them. On walls the sheets can run vertical or horizontal, because the table accepts the strength axis either way.

Related calculators