Board and Batten Calculator
Batten spacing, count and length for an accent wall or board and batten siding.
A 10 ft wall, 1x3 battens (2 1/2 in actual), gaps near 12 in: 9 battens, gaps evened out to 12 3/16 in.
One wall, or one stretch between doors and windows, end to end.
A target: the calculator evens the gaps so both ends match. HGTV used 8 in.
Floor to the top of the top rail. HGTV used 60 in on an 8 ft wall; full height works too.
5 1/2 in for a 1x6; 0 if the battens run to the floor.
3 1/2 in for a 1x4; 0 if the battens run to the ceiling.
All four put a batten on every 48 in panel joint.
Real Cedar spaces 6 in boards 1/2 in apart; McIlvain leaves 1/8 to 3/16 in between wider boards; Bob Vila about 1/4 in indoors.
The count already buys whole boards. Add extra for bad boards: siding guides add about 10% (CertainTeed, Hunker).
Check before you build
- Batten left edges from the left end: 0, 14 11/16, 29 3/8, 44 1/16, 58 3/4, 73 7/16, 88 1/8, 102 13/16, 117 1/2 in.
- The 5th batten sits on the wall's center line.
- Least offcut: 3 boards of 16 ft, 3 battens from each.
- Find the studs first: nail battens into studs or the backer and glue them with construction adhesive (HGTV, Bob Vila).
- Built before 1978? The paint may contain lead: test it before you pull old baseboards or sand, because the dust is the hazard (EPA).
This works out spacing and counts, not structure or weatherproofing.
- Building: Accent wall
- Wall width: 120 in
- Gap you want: 12 in
- Ends: a batten at each end
- Height: 60 in
- Baseboard: 5.5 in
- Top rail: 3.5 in
- Batten: 1x3
- Board length: 8 ft
Batten and board sizes: nominal and actual width
| Nominal | Actual width | mm | Used as |
|---|---|---|---|
| 1x2 | 1 1/2 in | 38 | Batten |
| 1x3 | 2 1/2 in | 64 | Batten |
| 1x4 | 3 1/2 in | 89 | Batten |
| 1x6 | 5 1/2 in | 140 | Board |
| 1x8 | 7 1/4 in | 184 | Board |
| 1x10 | 9 1/4 in | 235 | Board |
| 1x12 | 11 1/4 in | 286 | Board |
A 120 in wide wall with 1x3 battens aimed at 12 in gaps takes 9 battens with 12 3/16 in gaps (14 11/16 in on center), each 51 in long for a 60 in high wall treatment: 9 boards of 8 ft.
How to space board and batten evenly
Take one batten off the wall width, divide by one batten plus the gap you want, round to whole spaces and share what is left: a 120 in wall with 1x3 battens and 12 in gaps gets 8 spaces, 9 battens and 12 3/16 in gaps. The gap you type is a target. The calculator rounds to a whole number of spaces and spreads the leftover so every gap is the same.
There are two ways to finish the ends. With a batten at each end, the first batten sits flush against one corner and the last against the other. With a gap at each end, the wall starts and ends with open board, and the gaps are the same size all the way across. Either way the layout is symmetric, so an odd count puts a batten on the wall’s center line and an even count puts a gap there. LP, HGTV and Bob Vila all lay out from the middle for that reason.
The clear gap is the open space between two battens. On center is the distance from the middle of one batten to the middle of the next: the gap plus one batten width. Spacing is a choice. HGTV set its battens 8 in apart, and McIlvain gives 8 to 16 in on center for siding. To mark the wall, measure every batten from the same end: with a batten at each end, the left edge of each one is its number, less one, times the on-center distance. The calculator lists every left edge for you.
How long to cut the battens on an accent wall
Take the treatment height and subtract the baseboard and the top rail: HGTV’s 60 in wall with a 1x6 baseboard (5.5 in) and a 1x4 top rail (3.5 in) takes 51 in battens. Floor to the top of the top rail is the height; if the battens run to the floor or the ceiling, type 0 for that piece.
HGTV builds the wall on a backer of 3/4 in plywood, which the plywood calculator counts. Find the studs first and nail the battens into studs or the backer, then glue them with construction adhesive. Built before 1978? The paint may contain lead, so test it before you pull old baseboards or sand, because the dust is the hazard (EPA).
Board and batten siding: panels, wide boards and batten laps
For battens over the joints between 4 ft wide panels, put a batten on every joint and lap each panel by at least 3/4 in (James Hardie); over wide boards, lap each board by at least 1/2 in (Real Cedar, McIlvain). James Hardie makes its vertical panels 4 x 8, 4 x 9 and 4 x 10 ft. Their joints fall on studs, and HardiePanel allows studs up to 24 in apart, LP panel siding up to 16 in. A second row of panels needs Z-flashing along the horizontal joint.
Between wide boards, Real Cedar spaces 6 in boards 1/2 in apart, McIlvain leaves 1/8 to 3/16 in between wider boards, and Bob Vila uses about 1/4 in indoors. The battens cover the gaps, so the bigger the gap, the wider the batten you need. The calculator warns when a batten laps a board by less than 1/2 in. Nail each board once per blocking line and each batten between the boards, so the boards can move.
Cutting fiber-cement panels makes silica dust: cut outdoors with a dust-collecting saw and wear a NIOSH-approved respirator. For lap and vinyl siding, use the siding calculator.
What the board and batten calculator leaves out: nails, glue, openings
It does not count nails, adhesive or caulk, because no maker gives a count, and it does not cut the plywood backer, lay out corner trim, work out wind nailing or draw wainscoting grids. It treats each wall as a plain rectangle: windows and doors are not taken off, so run it once for each stretch between openings. It counts battens and boards, buying whole boards by the length you pick; the extra box adds a share for bad boards, and leaving it blank buys the exact count. For nailing, follow the siding maker’s fastener table and your local building code.
Worked example
- Spaces: (120 - 2.5) ÷ (2.5 + 12) = 117.5 ÷ 14.5 = 8.1, rounded to 8, so 9 battens
- Gap: (120 - 9 × 2.5) ÷ 8 = 97.5 ÷ 8 = 12.1875 in, 12 3/16 in
- On center: 12.1875 + 2.5 = 14.6875 in, 14 11/16 in
- Batten length: 60 - 5.5 - 3.5 = 51 in
- All the battens: 9 × 51 ÷ 12 = 38.25 ft
- Boards: an 8 ft board (96 in) gives 1 batten of 51 in, so 9 boards
- Top rail and baseboard: 120 ÷ 96 = 1.25, round up to 2 boards each
Questions people ask
How far apart should board and batten be?
8 to 16 in on center is the range McIlvain, a siding lumber dealer, gives for board and batten siding, and HGTV set its accent-wall battens 8 in apart. No maker sets a rule indoors: pick a gap and the calculator evens it out so both ends match.
How many battens do I need for a 10 ft wall?
9 battens of 1x3 for a 120 in wall aimed at 12 in gaps, with a batten at each end: (120 - 2.5) ÷ 14.5 = 8.1, rounded to 8 spaces, plus one. The gaps come out at 12 3/16 in.
What size battens should I use?
1x3, 2 1/2 in wide, is Real Cedar's frequent pick with 1x10 boards, and LP pairs its panels with 5/8 x 2 1/2 in battens. For battens over the joints between 4 ft wide panels, James Hardie wants each batten to lap each panel by 3/4 in, so 1 1/2 in (a 1x2) is the narrowest.
Should board and batten start in the middle of the wall?
Yes: 1 batten sits on the center line when the count is odd, like the 5th of 9 in the example; with an even count a gap is centered. LP, HGTV and Bob Vila all lay out from the middle so both ends match.
How tall should a board and batten wall be?
60 in on an 8 ft wall in HGTV's project; there is no set height, and full height works too. Cut each batten to the height less the baseboard and the top rail: 60 - 5.5 - 3.5 = 51 in.